Skip to main content

Modern Farmhouse Table DIY 2019

I am SO excited to share today’s post with you! Almost seven years ago, we made our first DIY dining room table and have loved it so much through multiple homes and countless paint jobs. It was so well loved.

Recently, Collin and I were working on another project, a bench for the holiday house and I loved it SO much. You might remember Collin made a built-in breakfast table in this style a couple years back and it seemed like the right time to take on a more ambitious project: a DIY farmhouse table with whitewash stain.

It turned out SO gorgeous. The total cost to build the table was around $250—and it looks so much more expensive. I was thinking of getting some new chairs, but when I saw them with the new table even the chairs looked nicer, so I kept them for now. Let me know if you think they are too casual or just right … I’m curious!

OK, let’s get into the full DIY! I hope some of you use this tutorial to make your own.

Supplies:
-two 4″x4″ x 8′ douglas fir boards (x brace)
-six 2’x4 ‘x 8′ boards
-six 3/4″x 8″ x 8’ poplar boards (table top)
-three 3/4″ x 2.5″ x 8″ poplar boards (table top trim)
-white flat paint
-paint brush
–satin polyurethane 
-wood glue
-rubber gloves
-2″ wood screws
-1 3/4″ wood screws
–kreg square drive 1 1/4″ screws 
-felt furniture pads (optional)

Tools:
-drill
-miter saw
-nail gun & 1.5″ nail brands
-electric sander & 220 grit sand paper
-400 grit sandpaper
-chisel
-tape measure
-safety glasses
-dust mask
–kreg pocket hole kit
–kreg clamp

Before i start, i just want to say that i used poplar boards for this project because i knew we were going to white wash it and poplar is a lot prettier wood and won’t yellow over time (where as typical pine boards yellow pretty bad after only a few weeks with the white washing style.) Poplar is slightly more expensive than pine, but if you’re going with any sort of natural finish i highly recommend spending the extra money! If you’re going to be staining your table a dark color or painting it, then you can use the same size boards but all in pine to save a few dollars.

First, you’re going to need to build the base of the table! Start by cutting your 4″x4″x 8′ boards with your miter saw to 40″ with 50° angle cuts on both ends. The boards should be 40″ point to point as shown in the picture below.
Next, you’re going to need to cut chunks out of the center of the boards so that they interlock into each other and make one x shape. To do this, find the center of each board, which if you’re following this exactly, will be 20″ because our boards are 40″. Once you have the center of the boards marked with a pencil, lay them on the ground, one on top of the other until the middles of each board are lined up perfectly. Double and triple check by measuring that they are perfectly even and then with a pencil trace where the two boards meet together on each board. Always remember to wear your safety glasses and dust mask!

Next, lay your board on your miter saw and adjust the blade to match the angle you traced on your board. Most miter saws let you adjust the depth to which it will let you cut. If your miter saw has this feature, then set it to exactly half of the 4″ board at 2″ deep and make a bunch of little cuts where you traced. Once you make a bunch of small cuts, you can break the slices of the board out and use a chisel to clean up whatever didn’t break out as shown above. Repeat the process with the other board. If your miter saw doesn’t have the depth adjustment feature, you can mark the 2″ on your board and make the cuts very carefully, making sure you don’t cut past your mark.

Using wood glue and 2″ wood screws, screw the two pieces together with the screws on the side that will face the inside of the table (you can pick whichever side looks best to face the outside).

Next, cut two 2″x4″x8′ boards for the top and bottom with the same 50° angle on each as well as two 8″ pieces for the feet. Attach the 2″x4″ pieces you cut to the x brace with glue and wood screws. Repeat this whole process to make the second leg for the table. Take your electric sander with 220 grit sandpaper and give both of your legs a good sanding to smooth them out and make them look nicer because these boards can tend to be kind of rough. You won’t regret this process! it will make your table look a lot more expensive in the end. Definitely don’t forget your safety glasses and dust mask! Whenever i get impatient and forget them i always regret it.

Next, cut three of your 2″x4″x8′ boards down to 5′ and using a kreg pocket hole kit, drill four pocket holes on each side of each 5′ board, two pocket holes per side of each board. In addition, cut three 2.5′ pieces from the same 2’x4′ boards. The 2.5′ pieces do not need pocket holes in them. Sand all of these pieces with your electric sander.

Attach the three 5′ boards to each leg as shown in the picture above. One attached in the middle of each x and the other two on either side of the top of each leg, 2.5′ apart and flush with the top. Next, attach your smaller 2.5′ boards in between the two top 5′ boards, but attach them horizontally instead of vertically. Screw in each board from the outside 5′ boards into the ends of the smaller 2.5′ boards as shown above. The 2.5′ boards will act as braces for your table top boards. Now the base of the table is done!

Next, build the table top! Take all six of your 3/4″x 8″x 8″ boards and cut them all down from 96″ to 90″, making sure they are all exactly the same length! Now take a good look at each side of each board and decide which side you will want to be the top of the table and lay each board face down so the top of the table is facing the floor. Cut two 4′ pieces of your 2’x4′ boards and place them on either end of your 6 table top boards and using some wood glue and screws, attach the them to each end. Flip your table top over so the top side is facing upwards.Next, with your miter saw cut two of your three 3/4″x2.5″x 8′ boards to 90″ with 45° angles at each end and attach them to each of the long sides of the table top using wood glue and a nail gun with 1.5″ nail brands. Cut the other 3/4″x 2.5″x 8″ board to two 48″ pieces with 45° cuts and attach them to the ends of the table the same way. Take your electric sander and give the table top a good even sanding, making sure to round the edges slightly so they aren’t so sharp. Place the table top onto the table base and position it so there is an even amount of distance on all sides of the table and screw the table top onto the base by using 1 3/4″ screws and screwing them through the 1.5′ horizontal brace pieces that are a part of the base, up into the table top. It’s important to use the correct length screw because you don’t want them to be too long and come out the top of the table!

Make a mixture of equal parts white flat paint and water and mix thoroughly and wearing some rubber gloves, take a rag and dip it in your paint and water mixture and rub evenly into the entirety of the table to create a white washed look. Repeat this if the first coat isn’t quite white enough. Once the paint and water mixture is dry, take satin polyurethane and paint it onto the entire table and let dry for the brands recommended time and then do one or two more coats on the table top just to give it a the maximum chance of avoiding staining from the inevitable spilled glass of wine. Once completely dry, take your 400 grit sandpaper and by hand, lightly sand the whole table to smooth out the rough polyurethane. This will give your table a perfectly smooth finish that feels very expensive! if your table is going to be on hardwood or tile and not carpet or a rug, put some felt furniture pads on the bottom of the feet. That’s it, your table is done!

If you use our DIY to build a table, we’d LOVE TO see it! Please tag us in a photo on Instagram! This is a large project, but it’s well worth it for the huge savings and chance to customize it with your perfect stain color.

xx! Elsie + Collin

Credits//Author: Elsie Larson. DIY: Collin DuPree. Photography: Amber Ulmer. Photos edited with A Color Story Desktop.
Etiketler:

Comments

Post a Comment

Popular posts from this blog

These Benches Provide More Than Just a Place to Sit

Short, long, wooden, metal, upholstered or padded — benches come in an endless array of styles and materials. It’s a good thing too because a stylish bench can add a bit of flair and a lot of convenience to any room in the house. Historical sources say that benches were a common type of simple seat in the era when only the most important people actually got to sit in a chair. Today, this humble piece of furniture has evolved from a second-class seat to a very functional element that can also be very stylish. Without a doubt, there’s a bench that fits the decor and size of your room, so check out these beautiful options. Luxuriously Padded View in gallery This hand-crafted marvel is the Margot Bench from Chapter and Verse furniture. This particular model is made from steam-bent American Black Walnut, with a marvelously upholstered top. The textural, channel-tufted jacquard textile is in great contrast with the hand-rubbed oil finish on the base. The handsome piece would be ste...
Post a Comment
Read more

25 Racing Car Beds For Children Rooms

Kids love racing cars and it’s not that difficult to understand why. They’re fast, flashy, colorful, noisy and pretty cool plus we now have a bunch of animations that basically revived the trend in a big way. With that in mind, you have to admit that having a racing car bed is pretty awesome, especially as a kid. You don’t have to be a Nascar fan to see it. View in gallery Most racing car beds manage to combine a fun design with a safe structure Racing car beds are usually small and designed just for children. They feature bold and vibrant colors that make them stand out and make the children like them even more. Red and blue are very common colors for such pieces. They also usually have numbers on them and those checkerboard patterns on the sides. Building a racing car bed is actually a very interesting concept. It’s a two-in-one piece. View in gallery A teenage kids room featuring a real racing car View in gallery It’s not a bad idea to also decorate the rest of the room in ...
Post a Comment
Read more

Streamlined Bedroom Decor Ideas to Make Every Night Restful

Let’s face it: You spend more time in your bedroom than any other room in the house. And, even though few people will probably see it, the master bedroom really does have to be comfortable and welcoming so that it’s a pleasant place to spend all those hours. It’s such a personal area that it should reflect your personality while being stylish and well organized because it can be very difficult to rest in a roomful of disorganized clutter. Obviously, the main focus of the space has to be the bed, but aside from storage for your clothing, the only other furnishings you definitely need in the bedroom are some sort of bedside tables or nightstands. Any other pieces you add, such as a chair, bench or other seating, will be driven by the size of the space. Here are some fresh master bedroom decor ideas that are streamlined and make the perfect starting point for creating a restful haven. Modern Canopy Style A far cry from the frilly, fussy canopy beds that trap legions of dust, today’s c...
Post a Comment
Read more